Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® T KR 4355 G10 - PA6T/6-GF50 - BASF

Material Data Center offers the following functions for Ultramid® T KR 4355 G10:
unit conversion, PDF datasheet print, comparison with other plastics, application examples, snap fit calculation, beam deflection calculation, parameters for material models, CAE Interfaces

Check here, which other Ultramid T datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 물질의 비성질 - 도표
Any use of this information falls under the rules of our disclaimer.
제품 설명서
Glass fibre reinforced partially aromatic polyamide for injection moulding. High toughness, stiffness and strength, low water absorption, high melting point (285 °C).
Processing/Physical Characteristics건조/응축단위시험규격
ISO 데이터
성형 수축률, 평행 0.2 / * % ISO 294-4, 2577
성형 수축률, 수직 0.6 / * % ISO 294-4, 2577
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 18000 / - MPa ISO 527
파단시 강도 260 / - MPa ISO 527
파단시 신율 2.8 / - % ISO 527
챠피 충격 강도 , +23°C 100 / - kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 14 / - kJ/m² ISO 179/1eA
열적 특성건조/응축단위시험규격
ISO 데이터
녹는점, 10°C/min 285 / * °C ISO 11357-1/-3
하중하에서의 변형온도, 1.80 MPa 245 / * °C ISO 75-1/-2
선형 열팽창 계수, 평행 18 / * E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 55 / * E-6/K ISO 11359-1/-2
전기적 특성건조/응축단위시험규격
ISO 데이터
상대 유전뮬, 1MHz 4.7 / 4.8 - IEC 62631-2-1
소산 인자, 1MHz 200 / 300 E-4 IEC 62631-2-1
부피 저항 >1E13 / >1E13 Ohm*m IEC 62631-3-1
전기 압력 33 / 31 kV/mm IEC 60243-1
기타 특성건조/응축단위시험규격
물에서의 흡수성 4 / * % ISO 62와 유사
조건에서의 흡습성 0.6 / * % ISO 62와 유사
물질의 비성질건조/응축단위시험규격
ISO 데이터
점도수 130 / * cm³/g ISO 307, 1157, 1628
도표
응력-신율 , Ultramid® T KR 4355 G10 (건조), PA6T/6-GF50, BASF
응력-신율 , Ultramid® T KR 4355 G10 (응축), PA6T/6-GF50, BASF
시컨트탄성율-신율 , Ultramid® T KR 4355 G10 (건조), PA6T/6-GF50, BASF
시컨트탄성율-신율 , Ultramid® T KR 4355 G10 (응축), PA6T/6-GF50, BASF
응력-신율(등시) 23°C, Ultramid® T KR 4355 G10 (응축), PA6T/6-GF50, BASF
크립탄성율-시간 23°C, Ultramid® T KR 4355 G10 (응축), PA6T/6-GF50, BASF
곡선 크리프 23°C, Ultramid® T KR 4355 G10 (응축), PA6T/6-GF50, BASF
인장탄성율-온도 , Ultramid® T KR 4355 G10 (건조), PA6T/6-GF50, BASF
인장탄성율-온도 , Ultramid® T KR 4355 G10 (응축), PA6T/6-GF50, BASF
특징
생산 공정
사출 성형
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
기타 정보
사E성
PREPROCESSING
Pre/Post-processing, max. allowed water content: .15 %
Pre/Post-processing, Pre-drying, Temperature: 110 °C
Pre/Post-processing, Pre-drying, Time: 8 h

PROCESSING
injection molding, Melt temperature, range: 310 - 330 °C
injection molding, Melt temperature, recommended: 320 °C
injection molding, Mold temperature, range: 80 - 120 °C
injection molding, Mold temperature, recommended: 100 °C
injection molding, Dwell time, thermoplastics: 5 min
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.